![install oil catch can 2012 genesis 2.0t install oil catch can 2012 genesis 2.0t](https://gbpperformance.ca/24177-large_default/kn-typhoon-performance-air-intake-system-genesis-coupe-20t.jpg)
For example, I bought a basic can from eBay to run on my Chevy Cruze and I kept having problems. However, that doesn’t mean cheap ones are OK to run, either. But, just because it’s more expensive doesn’t mean that it’s better. I’ve used $110 cans and had issues. Some people pay upwards of $350 and that’s a personal choice. I’ve used cheap cans I built myself using an oil/water separator for an air compressor with great success. The cost of a catch can does not determine it’s effectiveness. How much should you spend on a catch can? So for boosted cars it’s recommended that you also have a catch can on the vent side in addition to the PCV side even on a healthy motor. If you have an older motor or have issues with your piston rings, you may have excessive blow by at wide open throttle which can force oil out through the vent in which case you would need to add a catch can to the vent side.įor forced induction cars, the PCV valve is closed under boost to prevent pressurizing the crank case, but pressure still builds in the crank case and where does it go? Through the vent. If you do see oil, then you have another issue. If you put a breather on the vent, you won’t see any more oil coming from the vent, assuming you have a healthy engine of course.
![install oil catch can 2012 genesis 2.0t install oil catch can 2012 genesis 2.0t](https://cdn.mishimoto.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/M/M/MMSHOW-103_1.png)
This is because at wide open throttle, the air going through the intake passes over the vent tube and creates a type of suction add a sufficiently restrictive intake tract and the issue becomes worse. Some people get confused because they see oil in the intake tract coming from the vent. Naturally aspirated cars (in general) don’t need a catch can on the vent side and can usually just run a breather. The PCV side needs a catch can weather you’re naturally aspirated or boosted. The vent side, however, may or may not need a catch can depending on your setup. This is why you see the PCV routed to the intake manifold and the vent routed to the intake tubing or the air box – two different parts. There are TWO parts to the PCV system, the inlet also called the vent and the outlet, or, the PCV valve.
![install oil catch can 2012 genesis 2.0t install oil catch can 2012 genesis 2.0t](https://i.ytimg.com/vi/EmAQwiOY3rI/maxresdefault.jpg)
The hardest part of installing a catch can is finding a place to mount it.
#Install oil catch can 2012 genesis 2.0t how to#
There seems to be a lot of confusion around catch cans and how to hook them up, but they are very simple devices with very simple installation. I only had 10,000 miles on the engine when I took this photo. If you’re thinking that you are exempt because you have a brand new car, think again. This oil was collected over a 4 week period of aggressive driving including a track day. This is an example of what a catch can does. Some have mesh that only lets air pass while trapping particles, some are baffled and some have a combination of the two. Some are just empty cylinders with an inlet and an outlet and nothing else. Any oil, moisture and other contaminants that would normally come out of the PCV value and go into the intake manifold will now flow into the catch can first, and the job of the catch can is to prevent this crap from going back into your intake.Ĭatch cans have different designs. A catch can sits between your PCV valve and your intake manifold. Over time this sludge builds up and will kill performance.ĭirty engines are not happy engines. Over time this oil will coat the intake manifold, intake valves and the tops of the pistons. Most PCV systems will be redirected back into the intake manifold which means anything that escapes from the crank case will end up in your cylinders and this means that you’re burning oil.
![install oil catch can 2012 genesis 2.0t install oil catch can 2012 genesis 2.0t](https://gensportunited.com/wp-content/uploads/2017/05/anatomyofastage4upgrade_zps72864553.png)
I won’t get into exactly how this works because that’s not the point here, but it’s important to note that it relies on vacuum from the intake manifold (or a source of vacuum in general). It also allows other things like moisture and fumes to be evacuated as well. This system allows the pressure that gets built up in the crankcase to be relieved. Engines have a positive crankcase ventilation system which everyone simply calls the PCV.